A waterborne matting agent is a solid additive, most often amorphous precipitated silica, that lowers the gloss of a water-based coating by creating microscopic roughness at the surface of the dried film. Choosing one is not just a matter of picking the finest powder on the shelf. In water, the matting agent has to wet out in a low-viscosity aqueous phase, stay suspended in the can, survive the pH and surfactant package of the binder, and still end up near the film surface when the water leaves. This guide explains how waterborne matting works, which parameters on a datasheet actually predict performance, typical formulation ranges, how to test a candidate grade, and how to diagnose the most common problems.
It is written for formulators building or reformulating water-based wood, plastic and industrial clear coats, and for purchasing teams who need to understand why two powders with similar particle size can give very different finishes.
How a waterborne matting agent lowers gloss
Gloss is specular reflection: the share of incoming light that leaves the surface at the mirror angle. A perfectly smooth film reflects strongly at that angle and looks glossy. A matting agent works by breaking up that smoothness on a scale of roughly one to several micrometres, so that more light is scattered in other directions and the film reads as satin, matte or dead-matte.
The roughness forms during drying. As water and co-solvent evaporate, the wet film shrinks in thickness and the binder particles pack and coalesce. Rigid matting particles do not shrink, so the binder layer draws down around them and their tops create small bumps on the surface. The more particles that sit close to the surface, and the larger they are relative to the dry film, the lower the gloss.
Waterborne systems add a complication compared with solvent-borne coatings. The volume solids of a water-based clear are often moderate, so the film still shrinks considerably, but the way it shrinks depends on the polymer dispersion, coalescent level, and drying conditions. Fast drying in a tunnel, high humidity or a thick wet film can all change how many particles end up in the surface zone, which is why gloss in waterborne mattes is sensitive to the process and not only the recipe.
Types of matting agents used in water-based coatings
Several families of materials are used to reduce gloss in waterborne coatings. In practice, silica dominates clear wood and plastic finishes because it combines high matting efficiency with good transparency, but the others have their place.
| Type | How it mats | Typical strengths | Typical limitations |
|---|---|---|---|
| Precipitated silica (often wax-treated) | Porous particles create surface micro-roughness | High efficiency, good clarity, easy high-speed dispersion, cost-effective | Untreated grades can settle hard; can raise viscosity at high dosage |
| Silica gel | Porous particles, similar mechanism | Narrow particle size distributions, good clarity | Often priced higher; behaviour varies by grade |
| Wax dispersions and micronised waxes | Wax migrates and forms a micro-textured surface | Soft feel, slip, scratch and burnish resistance | Limited gloss reduction alone; can affect recoatability |
| Organic matting beads (e.g. polyurethane, PMMA) | Spherical particles protrude from the film | Soft-touch feel, good burnish resistance | Larger particle sizes, higher cost, can reduce clarity |
| Mineral fillers (e.g. talc, calcium carbonate) | Coarse particles roughen the surface | Low cost in pigmented systems | Poor transparency; unsuitable for clear coats |
Many commercial formulas combine silica with a wax additive: the silica delivers most of the gloss reduction, and the wax adds slip, feel and resistance to burnishing. For a deeper look at silica itself, see our article on how to choose a silica matting agent.
The parameters that predict performance
A datasheet for a silica waterborne matting agent usually lists six to ten properties. These are the ones that matter most to the finished film, and what each tells you.
- Particle size (d50) and distribution. The median size sets the balance between matting power and smoothness. Larger d50 gives stronger gloss reduction per percent added but a rougher feel and more risk of visible texture on thin films. Finer d50 gives smoother touch and better clarity but needs more material for the same gloss. The top end of the distribution (often reported as d90 or d97) controls specks and Hegman readings.
- Pore volume. Highly porous particles have a low apparent density, so each gram contains more particles and delivers more matting. Pore volume is one of the main reasons two grades with the same d50 mat differently.
- Surface area (BET). Relates to the internal pore structure and to how strongly the silica interacts with water, surfactants and thickeners. It influences viscosity build and stability.
- Surface treatment. Wax or organic treatment makes particles easier to wet into the binder, reduces hard sediment, and can improve clarity and scratch resistance. Untreated silica is more hydrophilic and tends to thicken water-based systems more.
- Oil absorption. A practical proxy for porosity and binder demand. High values mean the silica will tie up more liquid, which affects viscosity and film properties at higher loadings.
- pH of suspension and moisture. Useful for compatibility checks and lot-to-lot consistency rather than performance on their own.
When comparing grades, look at the combination rather than any single number. Two powders with an identical d50 but different pore volume and treatment can give a several-unit difference in 60° gloss at the same dosage, and noticeably different viscosity and storage behaviour.
Formulating with a waterborne matting agent
There is no universal recipe, but most formulators follow a similar pattern when adding silica to a water-based clear coat.
Typical dosage
Silica matting agents in waterborne clears are commonly used in the low single-digit percent range on total formulation. Satin finishes may need only a small addition, while matte and dead-matte targets need more, and deep matte on thin films may need a coarser grade rather than simply more powder. Always build a dosage ladder (for example three to five levels) in your own base, because the curve of gloss versus dosage is specific to the binder, film thickness and drying conditions.
Order of addition
- Charge water, co-solvent or coalescent and the wetting and defoaming additives the formula calls for.
- Add the matting agent slowly under moderate stirring to avoid dust and lumps.
- Increase to high-speed dispersion and run until the powder is fully wetted and the fineness target is reached.
- Let down with the binder dispersion under lower shear, then add thickener, wax and remaining additives.
Some formulators pre-disperse the silica into part of the binder or prepare a silica slurry. Both work; the key is consistent shear and time from batch to batch. Our guide on dispersing silica matting agents without bead milling covers disperser settings in detail.
Interactions to watch
- Thickeners. Silica can interact with associative and cellulosic thickeners. Add the thickener after the matting agent and check viscosity again after 24 hours.
- Foam. Powder addition and high shear entrain air. Microfoam in a matte film can look like haze or pinholes, so choose a defoamer that is effective without causing craters.
- Coalescent level. Changing coalescent alters film formation speed and can shift gloss. Fix the coalescent before tuning matting agent dosage.
- Wax additives. Wax adds slip and burnish resistance and contributes a little matting, so adjust silica dosage after the wax level is set.
How to test a waterborne matting agent in the lab
A meaningful evaluation compares the candidate side by side with a reference in the same base, with identical dispersion and film build. A practical test set:
| Test | What it shows | Practical note |
|---|---|---|
| Gloss at 60° and 85° | Matting efficiency; sheen at grazing angle | Use 85° readings for low-gloss films where 60° values bunch together |
| Clarity over a black or dark-stained panel | Haze and grey cast in clear coats | Compare visually and, if available, with a colorimeter |
| Hegman fineness | Dispersion quality and coarse particles | Read at the same time after dispersion every batch |
| Viscosity (initial and after 24 h) | Thickening effect and rheology interactions | Record shear rate and temperature |
| Heat-age storage (commonly 50 °C) | Settling, sediment hardness, gloss drift | Check whether sediment stirs back easily |
| Feel, burnish and scratch | Surface touch and polishing under rubbing | Compare against a retained standard panel |
Draw down or spray at the dry film thickness used in production, and dry under conditions close to the real line. A lab panel dried overnight at room temperature can read quite differently from one that passed through a heated tunnel in a few minutes.
Common problems and their likely causes
- Haze or whitening in clear coats. Often caused by too much or too coarse a matting agent for the film, incomplete coalescence at high humidity, or microfoam. See our article on haze in matte clear coats.
- Hard sediment in the can. Low-viscosity water-based systems give dense particles time to settle. Wax-treated silica and an appropriate rheology package usually produce a soft, stir-back sediment.
- Gloss varying between batches or shifts. Check dispersion time and tip speed, film thickness, and drying temperature and airflow before blaming the raw material.
- Viscosity spikes. High dosage of an untreated or very high-surface-area silica can over-thicken. Consider a treated grade or a slightly coarser grade at lower dosage.
- Specks and rough feel. Usually incomplete dispersion, agglomerates from damp storage, or a grade too coarse for the film thickness.
- Burnishing. Matte films that turn glossy when rubbed often benefit from a wax additive or a harder binder, alongside the matting agent.
How Censilcoat grades fit waterborne formulations
Censilcoat manufactures wax-modified amorphous precipitated silica matting agents specifically for waterborne wood and plastic coatings. Every grade is benchmarked against a commonly used imported grade, so a lab can start its trial from a known reference. All grades share a pore volume of 1.6–1.8 mL/g and a surface area of 250–280 m²/g.
| Grade | d50 | Benchmark | Typical waterborne use |
|---|---|---|---|
| Censil660 | 5.0–5.3 μm | ED 30 | High-clarity water-white clear topcoats on dark wood |
| Censil651 | 4.9–5.2 μm | ED 2 | Fine touch in high-clarity semi-matte and matte clears |
| Censil351C | 4.8–5.1 μm | ED 3 | Fine universal grade balancing appearance and stability |
| Censil361C | 5.9–6.2 μm | ED 4 / OK 412 | Semi-matte and matte workhorse with higher matting efficiency |
| Censil1531D | 5.3–5.6 μm | — | Cost-optimized grade for first-round substitution |
| Censil1650A | 6.2–6.5 μm | ED 30 | Deep matte for premium plastic coatings and tactile furniture |
| Censil3851 | 8.5–9.0 μm | TS 100 | Extreme low gloss and hard plastic surfaces |
Recommended dosage is 1–4% on total formulation, and the grades are designed to disperse with high-speed stirring for 15–20 minutes, without bead milling. They are packed in 20 kg bags, first orders start at 500 kg, and a free 2 kg sample ships with TDS, SDS and a benchmark sheet. If you are replacing an imported grade in a water-based wood coating, the ED 4 alternative page and the OK 412 alternative page show how we document parallel comparisons. Full specifications are on the products page, and the solutions page maps grades to resin system and gloss target.